EQUIPMENT MACHINE
Minggu, 22 Maret 2015
Tambah Komentar
Here's what assistive devices are often used in the operation of the lathe.
Vise drill (Drill Chuck)
Kalu who is certainly all have to know. Yes, this is pencekam drill bit and that in the picture below is the capacity to gripping dai 1,5-13mm diameter. Usually there is also a 1-10mm and that can be gripped dai 3-16mm diameter.
Adapter Or Gloves
Stalk flashlight, drill bits and drill chuck stalk have some degree of size. So that we can use it all at the head off the lathe, then we need to use an adapter. For example, if we want to attach 32mm drill bit straight in the head off a small lathe would not fit, then we need a deduction sheath diameter as shown below. Vice versa, if too small then we wear gloves enhancer.
Keep the buffer (Steady Rest)
Used to help hold long objects that will get workmanship section ends. Mounted on the machine bed with lockable bolts nuts. The part that holds the workpiece is made with bronze or brass so not much damage the workpiece. However should teatap lubricated during use .
Running Buffer (Follow Rest)
Used to help hold the workpiece with a relatively small diameter and relatively long. Mounted on the transverse carriage / cross slide so it would move along the machine bed. Similarly, the fixed buffer, it must be lubricated during use.
Follow rest (running buffer)
Flashlights and Flashlight Play Dead
Used to help support the ends of a shaft-shaped workpieces or axle or shaft. With the aim that when turner, the object does not shake, bent, vibrate or off. Certainly before the end of the axle a hole to place the flashlight.
 |
| turn the flashlight off and flashlight |
| use rotary center |
Flashlight Pipe
Used with the same purpose but with the use of rotary flashlight flashlight dedicated pipe to pipe or axles which has a hole that can not be supported with regular rotary flashlight.
 |
| typographer pipe |
Vise drill (Drill Chuck)
Kalu who is certainly all have to know. Yes, this is pencekam drill bit and that in the picture below is the capacity to gripping dai 1,5-13mm diameter. Usually there is also a 1-10mm and that can be gripped dai 3-16mm diameter.
 |
| drill chuck |
 |
| use the drill chuck |
Collet Chuck
Chuck this model is used for gripping the drill bit in a certain diameter. She just had to loosen and tighten the settings for a particular size. Therefore, the process of change of the object that has the same size in a vise imi be faster.
Usually in a set consisting of several collet as shown below.
Chuck this model is used for gripping the drill bit in a certain diameter. She just had to loosen and tighten the settings for a particular size. Therefore, the process of change of the object that has the same size in a vise imi be faster.
Usually in a set consisting of several collet as shown below.
| collet chuck |
Adapter Or Gloves
Stalk flashlight, drill bits and drill chuck stalk have some degree of size. So that we can use it all at the head off the lathe, then we need to use an adapter. For example, if we want to attach 32mm drill bit straight in the head off a small lathe would not fit, then we need a deduction sheath diameter as shown below. Vice versa, if too small then we wear gloves enhancer.
 |
| adapter or gloves |
Used to help hold long objects that will get workmanship section ends. Mounted on the machine bed with lockable bolts nuts. The part that holds the workpiece is made with bronze or brass so not much damage the workpiece. However should teatap lubricated during use .
   |
| steady rest or stand still |
Used to help hold the workpiece with a relatively small diameter and relatively long. Mounted on the transverse carriage / cross slide so it would move along the machine bed. Similarly, the fixed buffer, it must be lubricated during use.
Follow rest (running buffer)
  |
| follow rest or running buffer |
Belum ada Komentar untuk "EQUIPMENT MACHINE"
Posting Komentar
Terima kasih sudah mampir dan membaca blog saya, jika berkenan silahkan tinggalkan komentar