MAIN COMPONENTS MILLING MACHINE

Hi friends, how they say today? This time I will review the main components of the milling machine, if you do not know what the milling machine can be seen in previous articles sense milling machine, just ok

The main components of the milling machine are:

KNIFE FRAIS

Various milling knife that is often used is as follows:

1.Pisau Frais Sides

Used to mengefrais flat surface of the workpiece by using horizontal frias engine. In use the blade milling, there are three types: type H for hard steel, type N for steel medium (normal) and type W for mild steel.

Figure: Knife Frais

2.cutter Frais Front
This knife has two cutting edge direction that the front and side. The blades are used for horizontal and vertical surfaces menfrais workpiece using a vertical milling machine.
3.cutter Frais Flow Side and Front
Also called frais knife slit (slotting cutter). Use to create a groove or slit by using a milling machine
4.cutter Frais Saws
Also called split knife (slitting cutter). Used to divide or cut the workpiece and make a groove.
5.cutter Frais Forming
Also called a form milling cutter. Used to form the surface of the workpiece.
6.cutter Frais Gear
Used to make gears. These knives are two types of measure, namely the system module for size mm and DP systems (pitch diameter) to an inch.
7.cutter Frais Angle
Used to create angled surfaces. These knives are of two kinds, namely knives and knife fromage frais single angle double angle.
8.cutter Frais Finger
Also called end mill cutter, used to make the groove, hole enlargement and manufacture of terraced surface. Blades are on the front and the side.
9.cutter Frais Flow Flow T and Stroke
T has a blade groove milling cutter on the front, back and sides. Angled groove blade is used to make shaped groove angle. Eyes are cut blades on the front and side. The blades are angled grooves in two forms, namely angled grooves blunt knife and knife groove taper angle.

EYE KNIFE HOLDER

Image: Arbor

1.Adaptor
Used to hold the blade face milling. The adapter is divided into two kinds, namely the adapter with an elongated wedge, used to hold the blade face milling large size binder having keyway and adapter with transverse pegs used to hold small face milling blade.


2.Koled
Used to hold a knife or blade fromage frais finger grooves that stemmed silendris. There are two types of koled, namely koled bikonikal, used to hold the blade milling silendris non-threaded and koled W is used to hold the blade milling silendris threaded.
3.Pengurung (Arbor)
Used to hold a knife or a milling finger grooves that stemmed large conical / tapered. Gloves are used to lock the blade arbor milling and locking nut allows you to lock the blade and scabbard milling arbor.
use please note the two main elements of the arbor, the arbor size and type of ulirnya. There are two types of size arbor arbor type A, is a short-sized arbor, do not need to be supported and not flexing during use. Arbor type B, is a long arbor size, need to be supported due to the size of the tip section length and yielding at the time of use. While the type of arbor screw is threaded screw left and right.

Image: Head Dividers

HEAD DIVIDER (dividing heads)
Used to obtain the distribution of the same distance between each. In dividing heads there are two components, namely the main component, consists of components that implement sharing and supporting components consist of the head off and gears.
Part of the main unit is equipped with a head divider divider plate with holes and crank divider directly related to the worm screw shaft dibble workpiece simultaneously rotate through the worm gear. The number of worm gear teeth is 40 units. Comparison of crank rotation divider with round worm gear (shaft workpiece holder) is 40: 1 means that when 40 rounds crank divider plate is rotated, the worm gear shaft rotates one full lap times.

Bagikan Artikel ini